Power should still be disconnected

At this time, FarmBot should not be plugged into any power source.

Step 1: Connect the Y motor

Route the Y motor cable through the slot in the cross-slide plate and connect it to the Y motor.

Step 2: Connect the water tubes

Connect the water tube coming from the y-axis cable carrier to the 90-degree barb and the NPT to barb adapter above the solenoid valve.

Connect the water tube coming from the top of the x-axis cable carrier to the NPT to barb adapter below the solenoid valve.

Screw the garden hose to barb adapter onto a garden hose of the appropriate length. Then connect the water tube coming from the bottom of the x-axis cable carrier to the garden hose to barb adapter.

Step 3: Check for leaks

Turn on the supply of water at your garden hose spigot and check the FarmBot for any leaks. If your municipal water pressure is abnormally high, you may need to add zip ties to the tube-to-barb connections to prevent the tubes from popping off. In rare circumstances you also may need to add plumber’s tape (PTFE tape) to the threaded connections at the hose or solenoid valve to prevent leaking.

Step 4: Connect the Z-axis cables

Connect the cables at the junction of the y-axis and z-axis cable carriers:

  • Vacuum pump cables labeled VAC
  • Z motor cables labeled ZY and ZZ
  • Camera cables labeled CAM

The camera and z motor cables use the same connectors

Pay close attention to the cable labels to ensure you are connecting CAM to CAM and ZY to ZZ. Take your time with this step because a mistake could permanently damage the electronics.

Pay special attention that you fully insert the 90-degree connectors together. This may require a multi-step process of pushing together, slightly tightening the thumb screws, pushing together again, and tightening some more. See the video below for detail.

Step 5: Route the X2 motor cable and LED strip

Attach the X2 motor cable to the X2 motor. Then route the cable and the LED strip through the 30mm horizontal cable carrier supports along the gantry main beam.

Step 6: Route all cables behind the electronics box

Route all of the cables down between the solenoid valve mount and the electronics box. You may need to temporarily disconnect the solenoid valve mount from the extrusion to facilitate fitting all of the cables in the space.

Step 7: Plug everything in

Power should still be disconnected

At this time, the FarmBot should not be plugged into any power source.

The diagram below illustrates the FarmBot Express electronics schematic. In the following steps you’ll connect each motor and peripheral one at a time, and finally the power supply.

Connect the peripheral cables to the Farmduino Express board. From left to right:

Connect the motor cables to the Farmduino Express board. From left to right:

  • Cable labeled X1 to the X1 MOTOR connector. (this should be pre-connected)
  • Cable labeled X2 to the X2 MOTOR connector.
  • Cable labeled Y to the Y MOTOR connector.
  • Cable labeled ZY to the Z MOTOR connector.

Connect the camera cable to one of the vertically oriented USB Type-C connectors labeled USB1 or USB2 on the Farmduino Express board.

Do not use the horizontally oriented USB Type-C connector

Plugging the camera into the horizontally oriented connector will prevent the Raspberry Pi from communicating with the Farmduino.

Connect the power supply cable to the 24V POWER IN connector on the Farmduino Express board.

Step 8: Flash FarmBot OS to the microSD card

Remove the micro SD card from the Raspberry Pi Zero and follow our FarmBot OS installation instructions to install the latest version of our software. Then reinsert the microSD card into the Pi.

Step 9: Mount the power supply

Mount the power supply to the bed using four wood screws. Then connect the power supply’s output to the power supply cable.

Step 10: Plug FarmBot into the power source

Before plugging in...

Once you plug in the power supply, your system will be powered. Once powered, you cannot add, remove, or change any motor cables, peripheral cables, etc, or you risk damaging the electronics and being electrically shocked.

If you need to make any changes, first unplug the power supply from the wall.

If everything looks good, and you understand the precautions needed around powered electronics, plug the power supply into a GFCI protected outlet. If an appropriate outlet is not close enough to plug in directly, use an extension cord of the appropriate length and the green power cord protector.

The mark of success

If all has gone well, FarmBot will begin booting up and you should see blinking lights!

If anything seems not right, suspicious, or hazardous, immediately unplug the power supply from the wall and contact us at contact@farm.bot.

What’s next?